Click on the Part Number for Pricing.
Click on the for Detailed Acrobat PDF Specifications.

IT(AV) per Device (Note 1)	25A	55A	65A	90A	95A	160A	250A
1	NTE5708	NTE5710	NTE5714	NTE5720	NTE5724	NTE5726	NTE5728
2		NTE5711		NTE5721
3		NTE5712		NTE5722
VRRM	1600V	1200V	1600V	1200V	1600V	1600V	1600V
VF (Max)	1.55V @ 75A	1.40V @ 165A	1.40V @ 270A	1.40V @ 270A	1.40V @ 270A	1.50V @ 502A	1.44V @ 785A
TJ	-40°C to +125°C	-40°C to +125°C	-40°C to +125°C	-40°C to +125°C	-40°C to +125°C	-40°C to +125°C	-40°C to +130°C
di/dt (TJ = +125°C)	100A/µs	100A/µs	100A/µs	100A/µs	100A/µs	500A/µs	500A/µs
dv/dt (TJ = +125°C)	500V/µs	500V/µs	500V/µs	500V/µs	500V/µs	500V/µs	500V/µs
ITSM (1/2 Cycle, 60Hz)	400A	1500A	1950A	1950A	1950A	5350A	8900A
I2T (t = 8.3ms)	670A2sec	9350A2sec	15800A2sec	15800A2sec	15800A2sec	131000A2sec	361000A2sec
IGT (Max @ +25°C)	150mA	150mA	150mA	150mA	150mA	200mA	200mA
VGT (Max @ +25°C)	3.0V	3.0V	3.0V	3.0V	3.0V	3.0V	3.0V
PG(AV)	500mW	500mW	500mW	500mW	500mW	2W	2W
VGM (Max, Reverse)	5V	5V	5V	5V	5V	5V	5V
RthJC (Per Module)	0.40°C/W	0.25°C/W	0.14°C/W	0.14°C/W	0.14°C/W	0.05°C/W	0.02°C/W
VISOL	2500VRMS	2500VRMS	2500VRMS	2500VRMS	2500VRMS	3000VRMS	3000VRMS
Diag. No.	422	422	422	422	422	609	610

Note 1. T_C = +85°C

Circuit 1

Circuit 2

Circuit 3

Diag. 422

Diag. 609

Diag. 610

POWERBLOCK NOTES:

MOUNTING:
Careful mounting of powerblocks on the heatsink is one of the most important requirements of reliable satisfactory application. The contact surfaces of powerblock and heatsink must be clean, free from contamination and damage. Finish and flatness of heatsink contact surface should be310mm. A thin and uniform film of interface thermal compound should be applied to contact surface of powerblock and heatsink. Fixing bolts have to be uniformly tightened with the specified mounting torque. Cross sections of busbars or cables have to be dimensioned so that heating up the powerblock will be avoided. This applies in particular for series connected fuses.

MAINTENANCE:
Powerblocks are maintenance-free. The assembly group should, however, be cleaned from time to time to ensure the insulation capability, the heat dissipation and thus the availability of the power converter.

WARNING:
Beryllium oxide is used in the powerblock assembly for insulation. Do not destroy the powerblock case because the beryllium oxide dust resulting from such action is hazardous if inhaled.