Hot-Air Rework Station

XY-HAP60 24V Hot Air Pencil w/7 pin Connector XY-HAP80 32V Hot Air Pencil XY-LF852D Xytronic LF-852D, 600 Watt Rework station. Temperature adjustable for removing QFP, SOP, PLCC or SOJ chips, etc. Static Free circuit design - safe for working with CMOs and ICs. Key Features: Sensor/Pump Failed Detection: If sensor circuit fails,the heater power is shut down Temperature "Lock-Out" Feature: The temperature can be locked with a password code. Auto Cooling Design: When the power switch is off, the cooling system will begin to work automatically, the tempeature falls down to 100c/212f to protect the heating element from burning Quic Heat Up: High power heating element. Momentary power can reach 600W SPECIFICATIONS Power Supply 100 ~ 120VAC or 220~240VAC Pump: Diaphram 115V or 120V/ 230V or 240V Air Flow Capacity 1.5L - 40L/Min Heating Element Nichrome ~ 600W Hot Air Temperature 100c-480dc/212f - 896f Dimension 283(W)*120(H)*190(D) mm XY-LF853D XYtronic LF 853D Multi function rework system. Soldering, Desoldering and Hot air system. Specializing in lead free soldering/desoldering and surface mount devices with temperature controlled hot air. Tools can be used simultaneously.   Key Features: Heater/Sensor Failed Detection: If the sensor circuit fails, the heater power is shut down. Energy Saver Mode: If the stations is left idle for 20 minutes, the energy saver feature will automatically engage, resetting the temperature to 150 deg. celsius from the previous setting. Temperature "Lock-Out" Feature: The temperature can be locked with a password code. ESD Safe and Spike Free Circuitry: The "Zero Voltage" electronic switching design protects voltage and current sensitive components (CMOS devices, etc) against damaging current and transient voltage spikes commonly produced by less efficient, mechanically switched stations. Delayed Suction: To eliminate the problem of solder clogging up the tip, a delayed switch feature has been incorporated for the unit that allows the pump to continue sucking for 1.5 seconds after the actuator switch is released.   Ships With: Soldering Iron with pre-loaded standard tip Desoldering Iron with pre-loaded standard tip Hot air wand with 4 nozzles 2 Iron holder Hot air gun holders Maintenance kit 426DLX Fume extractor AC power cord with plug Operation manual XY-LF855D LF-855D  Multi-Function SMD Rework/Solder Station.  Combing two stations in one, saving space and increasing efficiency. This unit is specially designed for Lead Free Soldering/Desoldering surface mount devices with temperature controlled hot air. Key Features: Heater/Sensor Failed Detection: If sensor circuit fails, the heater power is shut down.  Quick Heat Up: High power heating element. Momentary power can reach 600W. Temperature "Lock-Out" feature: The temperature can be locked with a password code - for production line management. Temperature Adjustable: For removing QFP, SOP, PLCC or SOJ chips etc., especially built in static free circuit design safety for sensitive elements like CMOS ICs. Auto Cooling Design: When the power switch is off, the cooling system will begin to work automatically, the temperature falls down to 100°C /212°F to protect the heating element from burning. Auto Protecting Function: When heating element reaches a high temperature which can be protected automatically - extending the life of the heating element. Hot Air Function: 600W High power heating element. Temperature adjustable, for removing QFP, SOP,PLCC or SOJ chips, etc. Static Free circuit design - safe for working with CMOs and ICs. Sensor/Pump Failed Detection, Auto-Cooling design. Heating element with Auto-Protection Function     MODEL LF-855D Multi-Function SMD Rework Station Power Voltage 220-240Vac 50Hz/ 100-120Vac 60Hz Power Consumption (MAX) 700W Fuse (Fast type) 5A (fast type) 10A (fast type) Weight 17 lbs                 Solder Power Consumption 90W Temperature Range 100°C - 520°C /212°F - 896°F Sleeping Temperature 100°C Temp. Correction Range +99°C - 99°C / +178°F -178°F Default Set 100°C F-1: "000" F-2: "00" F-3: "100" F-4: "C"           Hot Air Power Consumption 600W Air Flow 1.5L/Min - 40L / Min Temperature Range 100°C-480°C  / 212°F - 896°F Air Flow 00-99 Default Setting F-1: "000" F-2 "C" Temperature 100°C    Air Flow 00 Ships With: Soldering iron with pre-loaded standard tip Hot air wand with 4 nozzles Maintenance kit Rework tweezers Iron holder Hot air wand holder AC power cord and plug Operation manual XY-LF8800 The Xytronic LF-8800 100 Watt Solder and Desoldering Station, with  internal vacuum pump. Key Features: Heater/Sensor Failed Detection: If sensor circuit fails, the heater power is shut down. Temperature “Lock-Out” feature:  The temperature can be locked with a password code. ESD Safe and Spike Free circuitry: The “Zero Voltage” electronic switching design protects voltage and current sensitive components (CMOS devices, etc.) against damaging current and transient voltage spikes commonly produced by less efficient, mechanically switched stations. Delayed Suction: To eliminate the problem of solder clogging up the tip, a delayed switch feature has been incorporated for the unit that allows the pump to continue sucking for 1.5 seconds after the actuator switch is released Energy Saver Mode: If the station is left idle for 20 minutes, the energy saver feature will automatically engage, resetting the temperature to 150°C from the previous setting. Iron Working Option:  Both soldering, desoldering irons can be used at the same time. Optional SMD Tweezers: Specially designed for SMD chips, SOT, Flat pack IC’s etc. reworking. Optional Hot Air Pencil (HAP 80): Removes SMD chips and flat packs up to 25mm.     Ships With: Soldering iron with pre-loaded standard tip Desoldering iron with pre-loaded standard tip 2 iron holders Maintenace kit Rework tweezer kit 426DLX Fume extractor AC power cord and plug Operation manual **Specifications subject to changes**